View B156XW01-V2_6979559.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 ( ) preliminary specifications ( ) final specifications module 15.6 hd - color tft-lcd model name b156xw01 v2 (h/w:0a/1a) customer date checked & approved by date note: this specification is subject to change without notice. approved by date prepared by date nbbu marketing division / au optronics corporation www..net
2 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 contents 1. handling precautions............................ ................................................... ........ 4 2. general description ............................. ................................................... ......... 5 2.1 general specification.......................... ................................................... .............................5 2.2 optical characteristics........................ ................................................... .............................6 3. functional block diagram ........................ ................................................... .. 11 4. absolute maximum ratings........................ ................................................... 12 4.1 absolute ratings of tft lcd module ............. ................................................... .............. 12 4.2 absolute ratings of backlight unit ............. ................................................... .................. 12 4.3 absolute ratings of environment ................ ................................................... ................. 12 5. electrical characteristics ...................... ................................................... ...... 13 5.1 tft lcd module ................................. ................................................... ............................. 13 5.2 backlight unit................................. ................................................... .................................. 15 6. signal characteristic ........................... ................................................... ........ 17 6.1 pixel format image ............................. ................................................... ........................... 17 6.2 the input data format.......................... ................................................... .......................... 18 6.3 signal description/pin assignment.............. ................................................... ................. 19 6.4 interface timing ............................... ................................................... ............................... 21 6.5 power on/off sequence.......................... ................................................... ................. 23 7. connector description........................... ................................................... ..... 24 7.1 tft lcd module ................................. ................................................... ............................. 24 7.2 backlight unit................................. ................................................... .................................. 24 7.3 signal for lamp connector ...................... ................................................... ..................... 24 8. dynamic test .................................... ................................................... ........... 25 8.1 vibration test ................................. ................................................... .................................. 25 8.2 shock test spec: ............................... ................................................... .............................. 25 9. reliability..................................... ................................................... ................. 26 10. mechanical characteristics ..................... ................................................... 27 10.1 lcm outline dimension ......................... ................................................... ...................... 27 10.2 screw hole depth and center position .......... ................................................... .......... 29 11. shipping and package ........................... ................................................... .. 30 11.1 shipping label format......................... ................................................... ........................ 30 11.2 carton package ................................ ................................................... .......................... 31 11.3 shipping package of palletizing sequence...... ................................................... ....... 31 12. appendix: edid description ..................... ................................................... 32 www..net
3 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 record of revision version and date page old description new description remark 0.1 2008/06/30 all first edition for customer www..net
4 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 1. handling precautions 1) since front polarizer is easily damaged, pay attent ion not to scratch it. 2) be sure to turn off power supply when inserting or disconnecting from input connector. 3) wipe off water drop immediately. long contact with water may cause discoloration or spots. 4) when the panel surface is soiled, wipe it with abso rbent cotton or other soft cloth. 5) since the panel is made of glass, it may break or c rack if dropped or bumped on hard surface. 6) since cmos lsi is used in this module, take care of static electricity and insure human earth when handling. 7) do not open nor modify the module assembly. 8) do not press the reflector sheet at the back of the module to any directions. 9) in case if a module has to be put back into the pac king container slot after once it was taken out from the container, do not pr ess the center of the ccfl reflector edge. instead, press at the far ends of t he ccfl reflector edge softly. otherwise the tft module may be damaged. 10) at the insertion or removal of the signal interface connector, be sure not to rotate nor tilt the interface connector of the tft module. 11) after installation of the tft module into an en closure (notebook pc bezel, for example), do not twist nor bend the tft module even momentary. at designing the enclosure, it should be taken into consideratio n that no bending/twisting forces are applied to the tft module from outside. otherwise the tft module may be damaged. 12) cold cathode fluorescent lamp (ccfl) in lcd contain s a small amount of mercury. please follow local ordinances or regulations for d isposal. 13) small amount of materials having no flammability gr ade is used in the lcd module. the lcd module should be supplied by power complied with requirements of limited power source (iec60950 or ul1950), or be applied ex emption. 14) the lcd module is designed so that the ccfl in it i s supplied by limited current circuit (iec60950 or ul1950). do not connect the cc fl in hazardous voltage circuit. www..net
5 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 2. general description b156xw01 v2 is a color active matrix liquid crystal display composed of a tft lcd panel, a driver circuit, and backlight system. the screen format is intended to support the hd (1366(h) x 768(v)) screen and 262k colors (r gb 6-bits data driver) without backlight inverter. all input signals are lvds inte rface compatible. b156xw01 v2 is designed for a display unit of noteb ook style personal computer and industrial machine. 2.1 general specification the following items are characteristics summary on the table at 25 condition: items unit specifications screen diagonal [mm] 394.9 (15.6w) active area [mm] 344.232 x 193.536 pixels h x v 1366x3(rgb) x 768 pixel pitch [mm] 0.252x0.252 pixel format r.g.b. vertical stripe display mode normally white white luminance (iccfl=6.0ma) note: iccfl is lamp current [cd/m 2 ] 220 typ. (5 points average) 187 min. (5 points average) (note1) luminance uniformity 1.25 max. (5 points) contrast ratio 500 typ response time [ms] 8 typ / 15 max nominal input voltage vdd [volt] +3.3 typ. power consumption [watt] 6.5 max. weight [grams] 520 max. min. typ. max. length - 359.3 359.8 width - 209.5 210.0 physical size without inverter, bracket [mm] thickness - - 6.2 electrical interface 1 channel lvds surface treatment glare, hardness 3h, support color 262k colors ( rgb 6-bit ) temperature range operating storage (non-operating) [ o c] [ o c] 0 to +50 -20 to +60 rohs compliance rohs compliance www..net
6 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 2.2 optical characteristics the optical characteristics are measured under stab le conditions at 25 (room temperature) : item symbol conditions min. typ. max. unit note white luminance iccfl=6.0ma 5 points average 187 220 - cd/m 2 1, 4, 5. r l horizontal (right) cr = 10 (left) 40 40 45 45 - - viewing angle h l vertical (upper) cr = 10 (lower) 10 20 15 35 - - degree 4, 9 5p 5 points - - 1.25 1, 3, 4 luminance uniformity 13p 13 points - - - 2, 3, 4 contrast ratio cr 400 500 - 4, 6 cross talk % 4 4, 7 t r rising - - - t f falling - - - response time t rt rising + falling - 8 15 msec 4, 8 rx 0.620 0.650 0.680 red ry 0.310 0.340 0.370 gx 0.280 0.310 0.340 green gy 0.550 0.580 0.610 bx 0.120 0.150 0.180 blue by 0.090 0.120 0.150 wx 0.293 0.313 0.333 color / chromaticity coodinates white wy 0.309 0.329 0.349 ntsc % cie 1931 - 60 - 4 www..net
7 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 note 1 : 5 points position (ref: active area) 1 2 3 4 5 h / 4 h / 4 h /4 h /4 h w w / 4 w /4 w / 4 w /4 note 2 : 13 points position (ref: active area) w /4 w w /4 h h /4 h /4 h /4 h /4 7 9 1 0 w /4 1 8 w /4 1 0 1 0 1 0 1 0 2 3 1 3 1 2 4 5 6 1 1 note 3 : the luminance uniformity of 5 or13 points is defi ned by dividing the maximum luminance values by the minimum test point luminance w13 = maximum brightness of thirteen points minimum brightness of thirteen points maximum brightness of five points w5 = minimum brightness of five points www..net
8 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 note 4 : measurement method the lcd module should be stabilized at given temper ature for 30 minutes to avoid abrupt temperature change during measuring. in order to stabilize the luminance, the measurement should be executed after lighting backlight for 30 minutes in a stable, wind less and dark room , and it should be measured in the center of screen. note 5 definition of average luminance of white (y l ): measure the luminance of gray level 63 at 5 points y l = [l (1)+ l (2)+ l (3)+ l (4)+ l (5)] / 5 l (x) is corresponding to the luminance of the poin t x at figure in note (1). note 6 definition of contrast ratio: contrast ratio is calculated with the following for mula. contrast ratio (cr)= brightness on the white state brightness on the black state www..net
9 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 note 7 definition of cross talk (ct) ct = | y b C y a | / y a 100 (%) where y a = luminance of measured location without gray level 0 pattern (cd/m 2 ) y b = luminance of measured location with gray level 0 pattern (cd/m 2 ) note 8 : definition of response time: the output signals of bm-7 or equivalent are measur ed when the input signals are changed from black to white (falling time) and from white to black (rising time), respectively. the respons e time interval between the 10% and 90% of amplitudes. ref er to figure as below. s i g n a l ( r e l a t i v e v a l u e ) "black" tr tf "white" "white" 0% 10% 90% 100% www..net
10 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 note 9. definition of viewing angle viewing angle is the measurement of contrast ratio R 10, at the screen center, over a 180 horizontal and 180 vertical range (off-normal view ing angles). the 180 viewing angle range is broken down as follows; 90 () horizontal left and right and 90 () vertical, high (up) and low (down). the measurement direction is typically perpendicular to the display surface with the screen rotated about its center to develop the desired measurement viewing angle. www..net
11 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 3. functional block diagram the following diagram shows the functional block of the 15.6 inches wide color tft/lcd module: tft array/cell vdd lcd controller lcd drive board backlight unit 1366(r/g/b) x 3 x 768 gnd dc-dc converter ref circuit y-driver x-driver rxin0 rxin1 rxin2 rxclkin (4 pairs lvds) mdf76kbw-30s-1h or compatible mating housing jae f1-x30h jst bhsr-02vs-1 lamp connector (2pin) lcd connector www..net
12 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 4. absolute maximum ratings an absolute maximum rating of the module is as foll owing: 4.1 absolute ratings of tft lcd module item symbol min max unit conditions logic/lcd drive vin -0.3 +4.0 [volt] note 1,2 4.2 absolute ratings of backlight unit item symbol min max unit conditions ccfl current iccfl - 7.0 [ma] rms note 1,2 4.3 absolute ratings of environment item symbol min max unit conditions operating top 0 +50 [ o c] note 3 operation humidity hop 5 95 [%rh] note 3 storage temperature tst -20 +60 [ o c] note 3 storage humidity hst 5 95 [%rh] note 3 note 1: at ta (25 ) note 2: permanent damage to the device may occur if exceed maximum values note 3: for quality performance, please refer to au o iis (incoming inspection standard) . twb=39c operating range storage range www..net
13 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 5. electrical characteristics 5.1 tft lcd module 5.1.1 power specification input power specifications are as follows; the power specification are measured under 25 and frame frenquency under 60hz symble parameter min typ max units note vdd logic/lcd drive voltage 3.0 3.3 3.6 [volt] pdd vdd power - - 1.5 [watt] note 1/2 idd idd current - 350 450 [ma] note 1/2 irush inrush current - - 1500 [ma] note 3 vddrp allowable logic/lcd drive ripple voltage - - 100 [mv] p-p note 1 : maximum measurement condition black pattern note 2 typical measurement condition: mosaic pattern note 3 measure condition +5.0v +12.0v vcc r1 47k r2 1k vr1 47k sw1 sw mag-spst 1 2 f1 q3 ao6402 g d2 s d1 d5 d6 c1 1uf/16v q3 ao6402 g d2 s d1 d5 d6 c3 0.01uf/25v c2 1uf/25v (high to low) control signal (lcd module input) www..net
14 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 5.1.2 signal electrical characteristics input signals shall be low or high-impedance state when vdd is off. it is recommended to refer the specifications of th c63lvdf84a (thine electronics inc.) in detail. signal electrical characteristics are as follows; parameter condition min max unit vth differential input high threshold (vcm=+1.2v) - 100 [mv] vtl differential input low threshold (vcm=+1.2v) -100 - [mv] vcm differential input common mode voltage 1.125 1.375 [v] note: lvds signal waveform vth vtl vcm vss www..net
15 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 5.2 backlight unit ccfl parameter guideline for ccfl inverter selectio n (ref. remark 1) parameter min typ max units condition ccfl current(iccfl) 2.0 6.0 7.0 [ma] rms (ta=25 ) note 1, 6 ccfl frequency(fccfl) 45 60 80 [khz] (ta=25 ) note 2,3 ccfl startup voltage(vs) 1520 [volt] rms (ta= 0 ) note 4 ccfl startup voltage(vs) 1265 [volt] rms (ta= 25 ) note 4 ccfl voltage (reference) (vccfl) - 720 800 [volt] rms (ta=25 ) note 5 ccfl power consumption (pccfl) - 4.40 4.80 [watt] (ta=25 ) note 5 ccfl life-time 12,000 - - hour (ta=25 ) note 7 to optimun tft lcd performance, the lamp inverter p wm frequesncy define as:210 +/-5 hz remark 1 : typ are auo recommended design points. 1-1 all of characteristics listed are measured unde r the condition using the auo test inverter. 1-2 in case of using an inverter other than listed, it is recommended to check the inverter carefully. sometimes, interfering noise stripes app ear on the screen, and substandard luminance or flicker at low power may happen. 1-3 in designing an inverter, it is suggested to ch eck safety circuit very carefully. impedance of ccfl, for instance, becomes more than 1 [m ohm] whe n ccfl is damaged. 1-4 generally, ccfl has some amount of delay time a fter applying starting voltage. it is recommended to keep on applying starting voltage fo r 1 [sec] until discharge. 1-5 ccfl discharge frequency must be carefully chos en so as not to produce interfering noise stripes on the screen. 1-6 reducing ccfl current increases ccfl discharge voltage and generally increases ccfl discharge frequency. so all the parameters of an in verter should be carefully designed so as not to produce too much leakage current from high-v oltage output of the inverter. www..net
16 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 note 1 : it should be employed the inverter which has dut y dimming, if iccfl is less than 4ma. note 2: ccfl discharge frequency should be carefully deter mined to avoid interference between inverter and tft lcd. note 3: the frequency range will not affect to lamp life a nd reliability characteristics. note 4: the output voltage of inverter should be able to gi ve out a power after ballast capacitor , the generating capacity has to be larger than a lamp st artup voltage , otherwise backlight may has blinking for a moment after turns on or can not be turned on. note 5: calculator value for reference (i ccfl v ccfl =p ccfl ) note 6: requirements for a system inverter design, which is intended to have a better display performance, a better power efficiency and a more r eliable lamp, are following. it shall help increase the lamp lifetime and reduce leakage current. a. the asymmetry rate of the inverter waveform shou ld be less than 10%. b. the distortion rate of the waveform should be wi thin 2 10%. * inverter output waveform had better be more simil ar to ideal sine wave. note 7: it is an edge-type blu with single ccfl, the life- time define as the brightness decay to 50% of original value and under normal operation. www..net
17 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 6. signal characteristic 6.1 pixel format image following figure shows the relationship of the inpu t signals and lcd pixel format. r g b r g b r g b r g b r g b r g b r g b r g b 1 1366 1st line 768th line www..net
18 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 6.2 the input data format signal name description r5 r4 r3 r2 r1 r0 red data 5 (msb) red data 4 red data 3 red data 2 red data 1 red data 0 (lsb) red-pixel data red-pixel data each red pixel's brightness data consists of these 6 bits pixel data. g5 g4 g3 g2 g1 g0 green data 5 (msb) green data 4 green data 3 green data 2 green data 1 green data 0 (lsb) green-pixel data green-pixel data each green pixel's brightness data consists of thes e 6 bits pixel data. b5 b4 b3 b2 b1 b0 blue data 5 (msb) blue data 4 blue data 3 blue data 2 blue data 1 blue data 0 (lsb) blue-pixel data blue-pixel data each blue pixel's brightness data consists of these 6 bits pixel data. rxclkin data clock the signal is used to strobe the pixel data and de signals. all pixel data shall be valid at the falli ng edge when the de signal is high. de display timing this signal is strobed at the fal ling edge of rxclkin. when the signal is high, the pixel data sh all be valid to be displayed. vs vertical sync the signal is synchronized to rxcl kin . hs horizontal sync the signal is synchronized to rx clkin . note: output signals from any system shall be low o r high-impedance state when vdd is off. www..net
19 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 6.3 signal description/pin assignment lvds is a differential signal technology for lcd in terface and high speed data transfer device. pin# signal name description 1 vss power ground 2 vdd + 3.3v power supply 3 vdd + 3.3v power supply 4 vedid + 3.3v edid power 5 aging aging mode power supply 6 clkedid edid clock input 7 dataedid edid data input 8 rxin0n -lvds differential data input 9 rxin0p +lvds differential data input 10 vss power ground 11 rxin1n -lvds differential data input 12 rxin1p +lvds differential data input 13 vss power ground 14 rxin2n -lvds differential data input 15 rxin2p +lvds differential data input 16 vss power ground 17 ck1inn -lvds differential clock input 18 ck1inp +lvds differential clock input 19 vss power ground 20 x --- 21 x --- 22 vss power ground 23 x --- 24 x --- 25 vss power ground 26 x --- 27 x --- 28 vss power ground 29 x --- 30 x --- www..net
20 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 note1: start from right side note2: input signals shall be low or high-impedance state when vdd is off. internal circuit of lvds inputs are as following. the module uses a 100ohm resistor between positive and negative data lines of each receiver input r r r r lvds receiver signal input pin no. 9 11 12 14 15 17 18 8 rxin0+ rxin0- rxin1+ rxin1- rxin2+ rxin2- rxclkin+ rxclkin- www..net
21 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 6.4 interface timing 6.4.1 timing characteristics basically, interface timings should match the 1366x 768 /60hz manufacturing guide line timing. parameter symbol min. typ. max. unit frame rate - -- 60 - hz clock frequency 1/ t clock 65 72 90 mhz period t v 776 806 1023 active t vd 768 768 768 vertical section blanking t vb 8 38 255 t line period t h 1396 1486 2047 active t hd 1366 1366 1366 horizontal section blanking t hb 30 120 681 t clock note : de mode only www..net
22 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 6.4.2 timing diagram www..net
23 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 6.5 power on/off sequence vdd power and lamp on/off sequence is as follows. i nterface signals are also shown in the chart. signals from any system shall be hi-z st ate or low level when vdd is off. power sequence timing value parameter min. typ. max. units t1 0.5 - 10 (ms) t2 0 - 50 (ms) t3 0 - 50 (ms) t4 400 - - (ms) t5 200 - - (ms) t6 200 - - (ms) t7 0 - 10 (ms) www..net
24 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 7. connector description physical interface is described as for the connecto r on module. these connectors are capable of accommodating the f ollowing signals and will be following components. 7.1 tft lcd module connector name / designation for signal connector manufacturer hirose or compatible type / part number mdf76kbw-30s-1h mating housing/part number 7.2 backlight unit physical interface is described as for the connecto r on module. these connectors are capable of accommodating the f ollowing signals and will be following components. connector name / designation for lamp connector manufacturer jst type / part number bhsr-02vs-1 mating type / part number sm02b-bhss-1-tb 7.3 signal for lamp connector pin # cable color signal name 1 red lamp high voltage 2 white lamp low voltage www..net
25 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 8. dynamic test 8.1 vibration test test condition: acceleration: 1.5 g , sine wave frequency: 10 - 500hz sweep: 30 minutes each axis (x, y, z) 8.2 shock test spec: test condition: acceleration: 220 g , half sine wave active time: 2 ms pulse: +/-x,+/-y,+/-z , one time for each side remark: 1. ambient condition is 25 + 5 , relative humidity : 40% ~ 70% 2. non-packaged and non-operation www..net
26 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 9. reliability items required condition note temperature humidity bias ta= 40 , 90%rh, 300h high temperature operation ta= 50 , dry, 300h low temperature operation ta= 0 , 300h high temperature storage ta= 60 , 35%rh, 300h low temperature storage ta= -20 , 50%rh, 300h thermal shock test ta=-20 to 60 , duration at 30 min, 100 cycles esd contact : 8 kv air : 15 kv note 1 note1: according to en 61000-4-2 , esd class b: some perf ormance degradation allowed. no data lost . self-recoverable. no hardware failures. remark: mtbf (excluding the ccfl): 30,000 hours with a con fidence level 90% www..net
27 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 10. mechanical characteristics 10.1 lcm outline dimension www..net
28 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 note: prevention ic damage, ic positions not allowed any overlap over these areas. www..net
29 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 10.2 screw hole depth and center position screw hole minimum depth, from side surface = 2.30 0.30 mm (ref. drawing) screw hole center location, from front surface = 3. 7 0.2mm (ref. drawing) screw torque: maximum 2.5 kgf-cm www..net
30 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 11. shipping and package 11.1 shipping label format *note#1 : h/w 0a represents raydium source driver a nd novatek gate driver combination. *note#2 : h/w 1a represents novatek source driver a nd radium gate driver combination. www..net
31 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 11.2 carton package the outside dimension of carton is 455 (l)mm x 380 (w)mm x 355 (h)mm 11.3 shipping package of palletizing sequence www..net
32 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 12. appendix: edid description address function value value value hex hex bin dec 00 header 00 00000000 0 01 ff 11111111 255 02 ff 11111111 255 03 ff 11111111 255 04 ff 11111111 255 05 ff 11111111 255 06 ff 11111111 255 07 00 00000000 0 08 eisa manuf. code lsb 06 00000110 6 09 compressed ascii af 10101111 175 0a product code ec 11101100 236 0b hex, lsb first 12 00010010 18 0c 32-bit ser # 00 00000000 0 0d 00 00000000 0 0e 00 00000000 0 0f 00 00000000 0 10 week of manufacture 01 00000001 1 11 year of manufacture 12 00010010 18 12 edid structure ver. 01 00000001 1 13 edid revision # 03 00000011 3 14 video input def. (digital i/p, non-tmds, crgb) 80 10000000 128 15 max h image size (rounded to cm) 22 00100010 34 16 max v image size (rounded to cm) 13 00010011 19 17 display gamma (=(gamma*100)-100) 78 01111000 120 18 feature support (no dpms, active off, rgb, tmg blk#1) 0a 00001010 10 19 red/green low bits (lower 2:2:2:2 bits) e6 11100110 230 1a blue/white low bits (lower 2:2:2:2 bits) b5 10110101 181 1b red x (upper 8 bits) a3 10100011 163 1c red y/ higher 8 bits 57 01010111 87 1d green x 4f 01001111 79 1e green y 94 10010100 148 1f blue x 26 00100110 38 20 blue y 1e 00011110 30 21 white x 50 01010000 80 22 white y 54 01010100 84 23 established timing 1 00 00000000 0 24 established timing 2 00 00000000 0 25 established timing 3 00 00000000 0 www..net
33 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 26 standard timing #1 01 00000001 1 27 01 00000001 1 28 standard timing #2 01 00000001 1 29 01 00000001 1 2a standard timing #3 01 00000001 1 2b 01 00000001 1 2c standard timing #4 01 00000001 1 2d 01 00000001 1 2e standard timing #5 01 00000001 1 2f 01 00000001 1 30 standard timing #6 01 00000001 1 31 01 00000001 1 32 standard timing #7 01 00000001 1 33 01 00000001 1 34 standard timing #8 01 00000001 1 35 01 00000001 1 36 pixel clock/10000 lsb 20 00100000 32 37 pixel clock/10000 usb 1c 00011100 28 38 horz active lower 8bits 56 01010110 86 39 horz blanking lower 8bits 78 01111000 120 3a horzact:horzblnk upper 4:4 bits 50 01010000 80 3b vertical active lower 8bits 00 00000000 0 3c vertical blanking lower 8bits 26 00100110 38 3d vert act : vertical blanking (upper 4:4 bit) 30 00110000 48 3e horzsync. offset 30 00110000 48 3f horzsync.width 20 00100000 32 40 vertsync.offset : vertsync.width 34 00110100 52 41 horz&vert sync offset/width upper 2bits 00 00000000 0 42 horizontal image size lower 8bits 58 01011000 88 43 vertical image size lower 8bits c1 11000001 193 44 horizontal & vertical image size (upper 4:4 bits) 10 00010000 16 45 horizontal border (zero for internal lcd) 00 00000000 0 46 vertical border (zero for internal lcd) 00 00000000 0 47 signal (non-intr, norm, no stero, sep sync, neg pol) 18 00011000 24 48 detailed timing/monitor 00 00000000 0 49 descriptor #2 00 00000000 0 4a 00 00000000 0 4b 0f 00001111 15 4c 00 00000000 0 4d 00 00000000 0 4e 00 00000000 0 4f 00 00000000 0 www..net
34 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 50 00 00000000 0 51 00 00000000 0 52 00 00000000 0 53 00 00000000 0 54 00 00000000 0 55 00 00000000 0 56 00 00000000 0 57 00 00000000 0 58 00 00000000 0 59 20 00100000 32 5a detailed timing/monitor 00 00000000 0 5b descriptor #3 00 00000000 0 5c 00 00000000 0 5d fe 11111110 254 5e 00 00000000 0 5f manufacture 41 01000001 65 60 manufacture 55 01010101 85 61 manufacture 4f 01001111 79 62 0a 00001010 10 63 20 00100000 32 64 20 00100000 32 65 20 00100000 32 66 20 00100000 32 67 20 00100000 32 68 20 00100000 32 69 20 00100000 32 6a 20 00100000 32 6b 20 00100000 32 6c detailed timing/monitor 00 00000000 0 6d descriptor #4 00 00000000 0 6e 00 00000000 0 6f fe 11111110 254 70 00 00000000 0 71 manufacture p/n 42 01000010 66 72 manufacture p/n 31 00110001 49 73 manufacture p/n 35 00110101 53 74 manufacture p/n 36 00110110 54 75 manufacture p/n 58 01011000 88 76 manufacture p/n 57 01010111 87 77 manufacture p/n 30 00110000 48 78 manufacture p/n 31 00110001 49 79 manufacture p/n 20 00100000 32 7a manufacture p/n 56 01010110 86 www..net
35 of 35 au optronics corporation product specification b156xw01 v0 document version : 0.3 7b manufacture p/n 32 00110010 50 7c 20 00100000 32 7d 0a 00001010 10 7e extension flag 00 00000000 0 7f checksum 26 00100110 38 www..net

▲Up To Search▲

Price & Availability of B156XW01-V2

	To Download B156XW01-V2 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .